Any suggestions ? :)

[Tecumsea]

You might begin to regret asking.....LOL.......It depends what you are trying to achieve! I've seen comments regarding the degree of ferocity in the face. My view is that the pose is more akin to someone about to take part in a Duel but not a mounted figure taking part in a charge, as I said it depends on what you first envisaged.

Really like what you have done so far and would buy it as it is!

Keith

 

[pokrad]

You might begin to regret asking.....LOL.......It depends what you are trying to achieve! I've seen comments regarding the degree of ferocity in the face. My view is that the pose is more akin to someone about to take part in a Duel but not a mounted figure taking part in a charge, as I said it depends on what you first envisaged.

Really like what you have done so far and would buy it as it is!

Keith

No, I was not going for the mounted one (although that would be typical for hussar), and this pose would hardly fit. As I said, wanted something connected to the "cravat" or "tie". And swearing came as natural extension of that
I never regret asking, hearing other people opinions is always a good thing, especially when they have knowledge - and many here do.
I saw that locks are long on the illustration, but made them smaller to avoid eventual casting problems. And it turns even darn locks had a purpose !?!?!?


To summarize:

1. Locks at least double as long (and obviously separate parts at casting)
2.The "mente" a bit bigger and heavier
3. ? Something else that absolutely has to be fixed ?

 

[Wayneb]

I agree with Keith......You might be best taking what you like as far as advice given and rely on your own creativity and vision, otherwise you might get lost in never never land. After all, this is "your" work. I know nothing about 3d printing, but I could never form an opinion with just
one view. I think it's looking good with much potential...…….For my taste, accurate or not....I like the hair on the chin.

Wayne

 

[pokrad]

I agree with Keith......You might be best taking what you like as far as advice given and rely on your own creativity and vision, otherwise you might get lost in never never land. After all, this is "your" work. I know nothing about 3d printing, but I could never form an opinion with just
one view. I think it's looking good with much potential...…….For my taste, accurate or not....I like the hair on the chin.

Wayne

Wayne, will do some more views when I fix the suggested things...

 

[blaster]

I think that the spacing between the buttons and lacing (frogging) is too sparse, going by your references.

best rgds, Victor

 

[pokrad]

At this point there is no part of the sculpt that I did not change !

It's a rope-fest !

Playing also with the texture of the "czako", but did not find the right way to do it yet...

 

[blaster]

Two more observations for your consideration:

The right hand lower sleeve has no wrinkling, unlike the upper part.

The shoulder sleeve on the pelisse appears quite small.

Rgds Victor

 

[pokrad]

Still not there, but here is a quick mockup turntable:

 

[pokrad]

And it might look like this color-wise :

It's just a quick color fill, not the actual texturing, just for illustration...

 

[grasshopper]

I really like it..and I haven’t been into uniforms for some time..but this pops!

 

[pokrad]

Over and out, thanks to everyone for helping...

 

[grasshopper]

When might it be available? Having offered my ideas, I have an interest in working on it..

 

[pokrad]

I have no idea, since my favorite printer service closed their business I have to find a new one...
Or if anyone is interesting of producing it, I am giving it away for free, as long as that someone promises it will be produced.

 

[grasshopper]

That sucks..

 

[pokrad]

Yap, it really suck. A good printing service that does not charge too much (and I can't pay much as I am producing only a few copies) is hard to find
But even without printing this is endless fun, and I learn something new every day

 

[grasshopper]

I agree about learning but surely there is a decent printing service out there...it’s a big hole...

 

[Nap]

Hi Pokrad

Been quietly following this really like the way you listen to constructive comments and act on and try them out

For me it should be commercial it's a nice lookng piece , details all over

....a suggestion ...extend the pelise hanging sleeve to the full length

Let's hope you find a new company and you show us more of your work

Thanks for sharing

Nap

 

[pokrad]

Thanks Nap.
Always kind and supporting, the good spirit of PF